Gear selector stem made of hardened and tempered steel with nickel-plating treatment to increase sliding as well as giving it an aesthetic touch by increasing its brightness. Ø 20 mm length 88.4 mm

Transmission gears made of special steel with straight teeth and recalculated ratio. They completely eliminate all the axial pressures, thereby reducing stress on the bearings. They are constructed using high-precision machine, casehardened, tempered and ground to provide silent running and long life.

Primary gears HTQ Malossi S.p.A. is pleased to offer its new series of final transmission gears. These new gears were created by exploiting our 20-year experience in designing and building gears. The new HTQ gears were designed and built with straight/helical teeth to minimise losses through friction and stress on the supports. Moreover, our gears increase ratios slightly enabling you to exploit the full power of your vehicle, thus significantly increasing its original performance potential.

Classic and avant-garde. HTQ Malossi gears for the Vespa PX inherit the elements of the first gears project produced by Malossi between the end of the 80s and the beginning of the 90s. Completely redesigned, these primary gears use a straight-tooth configuration instead of the standard helical teeth. Malossi has worked hard to guaranteed exceptional silence from the gears, obtained by special processing of the teeth and associated contact surfaces, finished with a maniacal attention to detail and checked on an involute measurement machine. HTQ Malossi gears are manufactured exclusively using…

Malossi is pleased to offer their customers its new final transmission gear assembly... THIRD SUPPORT Malossi, always attentive to rider's observations and requests, has focused on Minarelli-Yamaha, considering the CVT system has shown some deficiencies. At high RPMs, the driven pulley generates strong vibrations and oscillations to the primary gear shaft. To remedy this problem, an additional bearing, inserted into the original crankcase cover is used creating a third support for a redesigned longergear shaft. This modification prevents the gear shaft from flexing thus allowing the CVT…

Primary gears HTQ Malossi S.p.A. is pleased to offer its new series of final transmission gears. These new gears were created by exploiting our 20-year experience in designing and building gears. The new HTQ gears were designed and built with straight/helical teeth to minimise losses through friction and stress on the supports. Moreover, our gears increase ratios slightly enabling you to exploit the full power of your vehicle, thus significantly increasing its original performance potential.

Ruote eseguite con acciaio speciale da cementazione, le ruote sono ottenute con macchine dentatrici al CNC e le ruote sono rettificate nelle superfici di contatto. Nelle superfici di contatto tra gli ingranaggi abbiamo ottenuto delle piccole sacche utili al trasporto dell’olio per aumentarne e garantire la lubrificazione tra le pareti che scorrono tra loro. I numeri di denti sono stati calcolati per dare un rapporto di trasmissione ottimizzato. In tutte le ruote dove era possibile eseguirli sono stati praticati dei fori di alleggerimento tranne che nella zona di sezione di contatto tra ruota…

Transmission gears made of special steel with straight teeth and recalculated ratio. They completely eliminate all the axial pressures, thereby reducing stress on the bearings. They are constructed using high-precision machine, casehardened, tempered and ground to provide silent running and long life.

Primary gears HTQ Malossi S.p.A. is pleased to offer its new series of final transmission gears. These new gears were created by exploiting our 20-year experience in designing and building gears. The new HTQ gears were designed and built with straight/helical teeth to minimise losses through friction and stress on the supports. Moreover, our gears increase ratios slightly enabling you to exploit the full power of your vehicle, thus significantly increasing its original performance potential.

Primary gears HTQ Malossi S.p.A. is pleased to offer its new series of final transmission gears. These new gears were created by exploiting our 20-year experience in designing and building gears. The new HTQ gears were designed and built with straight/helical teeth to minimise losses through friction and stress on the supports. Moreover, our gears increase ratios slightly enabling you to exploit the full power of your vehicle, thus significantly increasing its original performance potential.

Transmission gears made of special steel with straight teeth and recalculated ratio. They completely eliminate all the axial pressures, thereby reducing stress on the bearings. They are constructed using high-precision machine, casehardened, tempered and ground to provide silent running and long life.

Transmission gears made of special steel with straight teeth and recalculated ratio. They completely eliminate all the axial pressures, thereby reducing stress on the bearings. They are constructed using high-precision machine, casehardened, tempered and ground to provide silent running and long life.

Transmission gears made of special steel with straight teeth and recalculated ratio. They completely eliminate all the axial pressures, thereby reducing stress on the bearings. They are constructed using high-precision machine, casehardened, tempered and ground to provide silent running and long life.

Wheels made with special case-hardened steel, obtained with CNC hobbing machines and ground in the contact surfaces. In the contact surfaces between the gears we have obtained small pockets useful for transporting the oil to increase and guarantee lubrication between the walls that slide between them. The numbers of teeth have been calculated to give an optimized gear ratio. In all the wheels, where it was possible to make them, lightening holes were made except in the area of the contact section between the wheel and the gear selector so as not to create breaking points. Kit with Z different…